This is a new refueler with some scratches (minor) on out side from handling.
Refueler 60 Cylinder Filling Systems info:
Fill Adsorbed Natural Gas Cylinders In Your Own Shop!
Refueler 60 makes it simple to take high pressure natural gas across the shop, across town or to a job site. Just connect Refueler 60 to an Adsorbed Natural Gas Cylinder and press the START button to begin the filling process.
Once started filling cylinders is automatic. Cylinders are pressurized to 275 psi and the Refueler 60 turns itself off without operator attention. Many G-TEC customers start the filling process at the end of the day, refill their cylinders over night and begin each day will full natural gas supplies.
Refueler 60 can fill one or up to four cylinders at once with a G-TEC Manifold. Cylinders attached for filling do not need to be at the same level of fullness - they will all be filled together and finish at the same time. Cylinders fill at the rate of one cubic foot per minute.
Typical Applications
G-TEC Refueler 60 Cylinder Filling systems are used wherever fuel gas is used portably. Maintenance and repair shops in large companies take natural gas on the shop floor to repair equipment. Companies that do not have a shop-wide fuel distribution manifold use G-TEC cylinders to take natural gas each work station for production. Others that do remote work fill cylinders overnight then take full cylinders on their trucks to job sites.
Technical Description and Installation
Refueler 60 is compact, just 20" wide, 18" deep and 16" tall and weighs about 90 pounds. Electrical requirement in North America is 120V 20 amp. An international version for 230V 50 Hz electrical systems is also available.
Refueler 60 is quiet, does not require any special site preparation and can be installed "anywhere" that is consistent with local codes and regulations for cylinder filling. The system includes a flexible 5' hose for connection to the building low pressure natural gas pipe and a shut off valve.
Refueler 60 should be installed indoors in an area where temperatures range between 40-90F / 5-32C.
This is a new refueler with some scratches (minor) on out side from handling.
Refueler 60 Cylinder Filling Systems info:
Fill Adsorbed Natural Gas Cylinders In Your Own Shop!
Refueler 60 makes it simple to take high pressure natural gas across the shop, across town or to a job site. Just connect Refueler 60 to an Adsorbed Natural Gas Cylinder and press the START button to begin the filling process.
Once started filling cylinders is automatic. Cylinders are pressurized to 275 psi and the Refueler 60 turns itself off without operator attention. Many G-TEC customers start the filling process at the end of the day, refill their cylinders over night and begin each day will full natural gas supplies.
Refueler 60 can fill one or up to four cylinders at once with a G-TEC Manifold. Cylinders attached for filling do not need to be at the same level of fullness - they will all be filled together and finish at the same time. Cylinders fill at the rate of one cubic foot per minute.
Typical Applications
G-TEC Refueler 60 Cylinder Filling systems are used wherever fuel gas is used portably. Maintenance and repair shops in large companies take natural gas on the shop floor to repair equipment. Companies that do not have a shop-wide fuel distribution manifold use G-TEC cylinders to take natural gas each work station for production. Others that do remote work fill cylinders overnight then take full cylinders on their trucks to job sites.
Technical Description and Installation
Refueler 60 is compact, just 20" wide, 18" deep and 16" tall and weighs about 90 pounds. Electrical requirement in North America is 120V 20 amp. An international version for 230V 50 Hz electrical systems is also available.
Refueler 60 is quiet, does not require any special site preparation and can be installed "anywhere" that is consistent with local codes and regulations for cylinder filling. The system includes a flexible 5' hose for connection to the building low pressure natural gas pipe and a shut off valve.
Refueler 60 should be installed indoors in an area where temperatures range between 40-90F / 5-32C.
